Payne HVAC Manuals, Parts Lists, Wiring DiagramsManuals, parts lists, wiring diagrams for Payne HVAC equipment:
We include immediate downloads of example installation & repair manuals and wiring diagrams for air conditioners, heat pumps, and heating equipment from a variety of manufacturers as well as contact information to obtain the exact manual or wiring diagram for your unit.
InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.
- Daniel Friedman, Publisher/Editor/Author - See WHO ARE WE?
Here we provide contact information and free downloads of Payne Owners Manuals, service manuals, technical guides.
Payne Furnace Error Code Decoder |
|
| Error Light Indicator | Meaning |
| Red LED 1 On Solid | Operating in Emergency Heat Mode |
| Red LED 2 On Solid | Microprocessor malfunction |
| Red LED 2 Flashing | Wiring error Line Hot/Neutral reversed |
| Yellow LED 3 On Solid | High Heat Mode |
| Green LED4 On Solid | Low Heat Mode |
| Code 11 | No faults in laste 5 run cycles |
| Code 12 | Blower calibration lockout |
Be sure to check the manual and error codes for your specific Payne HVAC equipment.
See this
Hi, I have a payne HVAC system. When I turn on the thermostat (it has a switch for heat and cold and another one for a fan) to either cool or heat the air blows but is neither hot nor cool (I also turn on the fan at the same time).
The unit on the roof does not engage, that is I hear no noise and the fan blade does not turn. What could be the problem?
I preface that the unit is quite old, although I haven't used it much as I live in Los Angeles closer to the ocean. I would appreciate any ideas you might have. Thanks On 2021-04-17 by dali H
Rooftop Air Conditioning unit is not turning on
Hi, and thanks for answering. The thermostat works when turning the fan and the heat. I could not adjust the temperature lower than what it is inside.
The override only works for adjusting the temp up. I therefore just tried the heat option. It turned on inside the house, but it only produced room temperature air.
I checked the unit on the rooftop and nothing was moving. I think the unit on the rooftop should be working even when turning the heat on, right?
I looked at the fuses in the power box, or whatever that box attached to the unit on the roof is called, and they look a bit blackened.
Again I don't know if that could be the problem or not. Thanks again and have a good evening. - On 2021-04-18 by dali H
Reply (mod) -
@dali H ,
It sounds as if your rooftop unit is not turning on. I can't tell from your text if that's something as simple as a disconnected thermostat wire or whether there's a bad control or whether a motor or compressor has failed.
SeeLOST COOLING CAPACITY: DIAGNOSTIC GUIDE A/C or HEAT PUMP
where you will see some basic diagnostic steps many of which can be completed by homeowner.You could try changing the fuses but if they blow again then you've got a seized motor or a short circuit and you need to leave the circuit off
...
Continue reading at MANUALS for HEATING & A/C SYSTEM CONTROLS or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.
Or see these
PAYNE AIR CONDITIONING at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.
Or see this
Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia
Or see
Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia
Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.
Search the InspectApedia website
If you posted comments here and no longer see what you wrote, please check for your comment in the Reader Q&A found above on this page.
In addition to any citations in the article above, a full list is available on request.