InspectAPedia®   -   Search InspectApedia

Nail plates installed to protect electrical wiring that might be punctured by drywall screws or nails (C) Daniel Friedman at InspectApedia.comCinderella Incinerating Toilet Installation Details -
LOCATION

Photo Guide to Details of Steps to Install the Cinderella Toilet

Here we provide photos and notes giving details of a successful installation of the Cinderella Incinerating Toilet.

This is article #2 of seven articles in this series. The full list of seven is included in the Recommended Articles list at the end of this page.

This article series describes the brands, properties, installation, and maintenance of incinerating toilets - a waterless system for onsite waste disposal where a septic system cannot be installed. Incinerating toilets use electricity or gas to produce heat which literally incinerates the waste.

InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.

- Daniel Friedman, Publisher/Editor/Author - See WHO ARE WE?

Cinderella Incinerating Toilet Installation Details

Cinderella incinerating toilet installation manual: Model: Cinderella Comfort, electric - cited & discussed at InspectApedia.com

Above: the cover of the instruction manual for the Cinderella Comfort incinerating toilet.

The manufacturer provides excellent instruction manuals for the installation of each Cinderella incinerating toilet model. Be sure to obtain and read and follow those instructions. Failure to do so could mean that your installation doesn't work properly or worse, that the installation is unsafe. Always start by reading the instructions.

[Click to enlarge any image]

In this article series we provide detailed photos and notes that expand on the manufacturer's instructions to show how we implemented them in a specific case.

These added "how to" details explain and illustrate exact details of every step in the installation of an incinerating toilet.

We include a few tricks of the trade that solve special problems such as how to mount a flat vent cover on a curved log exterior wall, and how to set up chimney sections to measure the correct lengths to which you should cut the material.

We also include details on adding additional chimney/vent bracing at the roof edge to solve what in our OPINION was a very wobbly and potentially problematic exterior vent installation.

Article Series Contents

Please visit the above link to this topic's home page for a complete list of all the steps included in the installation of a Cincerella incinerating toilet.

For ease of page loading and reading, we have divided the entire incinerating toilet installation procedure into a series of web pages listed there.

If you prefer to have all of this information together in a single printable document simply download CINDERELLA TOILET INSTALLATION INSTRUCTIONS - ALL [PDF]

Article Contents

...

Choose Incinerating Toilet Location & Electrical Hook-Up Connection Point

Incinerating Toilet Location Considerations

  • Location suitable for using a toilet, such as privacy

    Note: the toilet installation illustrated in this article is in a bathroom in a building that is not connected to an external water supply and where no septic system was available. The bathroom provides privacy for toilet users.

    Watch out: building users should be prepared for and accept that during an incineration cycle, the toilet's power vent will make make a whirring sound that can go on for an hour or longer. If installed just outside of a bedroom, some may not enjoy that noise.
  • Location where outdoor combustion air is available

    either by direct inlet for the Cinderella Classic (electric) and Freedom (gas) models, or where you can route the toilet's dedicated air inlet to an outdoor air source for the Cinderella Comfort (electric) model.

    The toilet does not need to be installed in a room with an exterior wall, but if not, there must be a supply of exterior air to support the incinerating toilet's combustion process.
  • Location must provide a sound and level floor
  • Location that provides sufficient clearance

    for sufficient chimney height to provide draft assist to the vent system (no bends allowed in chimney vent for the gas model).
  • Location where 120V or 240VAC electrical circuit is available

    for the Classic or Comfort electric incinerator toilets or where you can provide 12VDC for the gas model.

    A 10A 120v/240V (depending on model) electrical receptacle must be provided for the Cinderella Classic and Comfort (electric) models while the Freedom (Gas) model toilet will require a 12V electrical power supply.

    Watch out: plan the location of both the toilet and its wall receptacle so that the toilet doesn't block access to the receptacle itself or you either won't be able to plug it in or you may be forced to place the toilet further from the building wall than you wish.

...

Provide Electrical Connection for the Cinderella Toilet

240V electrical receptacle for powering the Cinderlla Comfort incinerating toilet (C) Daniel Friedman at InspectApedia.com

Electrically powered incinerating toilets might be provided in either 120VAC or 240VAC models, powering both the incinerator itself and the toilet's exhaust fan; gas powered incinerating Cinderella toilets will require a 12VDC (low voltage direct current for gas power) circuit to power the toilet exhaust fan. Here we installed a 240VAC receptacle on a dedicated circuit for this toilet.

Above in the center of the photograph you can see the electrical receptacle. The toilet itself requires a 10 Amp (2000 Watts) circuit. Often specialized 240VAC circuits wired in new construction will use wiring that can safely support 15A or 20A 240VAC.

Even though the toilet only draws 10A and even though a 15A electrical circuit can be and is normally wired with #14 copper wire, it's safe to use a larger gauge wire as long as all of the electrical connections can be made properly. (A too-large wire won't fit in some electrical connectors.)

The original construction in this building had provided an unused #10 copper wire circuit that we used to power the toilet's receptacle, connected from a 15A circuit breaker and routed to the single 240V receptacle shown in our photo.

Also shown above at the right side of our photo and again below are views of the wall rough-in opening for the Cinderella toilet's through-wall piping that will provide the combustion air inlet and combustion exhaust outlet.

Below: we've excerpted from Eaton's instructions for this receptacle to show how we wired it for a 240V circuit for this Cinderella Comfort incinerating toilet hook-up.

How to wire a 220V / 240 V / 250V AC Receptacle for the Cinderella Comfort Incinerating Toilet (C) Daniel Friedman at InspectApedia.com

Below: most of the nail plates to protect electrical wiring in this wall have been installed including for wires that pass in the wall above the rough-in opening left for routing the toilet air inlet and exhaust vent pipes.

Nail plates installed to protect electrical wiring that might be punctured by drywall screws or nails (C) Daniel Friedman at InspectApedia.com

Watch out: if you are not trained in proper and safe electrical wiring, hire someone who is qualified: you could be shocked or killed or could set the building on fire.

Watch out: the company warns that this toilet can draw 2000W for extended periods of time during an incineration cycle.

Therefore you should not try to power the toilet through a power converter, nor through a solar or battery powered electrical system. If your building does not have access to sufficient electrical power, you should consider ordering the Cinderella GAS toilet model.

 

 


Please continue reading the next article in this series on installing a Cinderella incinerating toilet - the link is just below.

© 2023 InspectApedia.com

...

Continue reading  at CINDERELLA INCINERATING TOILET INSTALLATION - CLEARANCES & WALL CUTS or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.

Or see these

Recommended Articles

Suggested citation for this web page

CINDERELLA INCINERATING TOILET INSTALLATION - LOCATION - at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.


Or see this

INDEX to RELATED ARTICLES: ARTICLE INDEX to TOILET INFORMATION

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia

Ask a Question or Search InspectApedia

Questions, answers, FAQs, and reader comments about incinerating toilets.

Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment below may be delayed: if your comment contains an image, photograph, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.

Only one image can be added per comment but you can post as many comments, and therefore images, as you like.
You will not receive a notification
when a response to your question has been posted.
Please bookmark this page to make it easy for you to check back for our response.
Our Comment Box is provided by Countable Web Productions countable.ca

Comment Form is loading comments...

Citations & References

In addition to any citations in the article above, a full list is available on request.



ADVERTISEMENT