Question? Just ask us!
Free Encyclopedia of Building & Environmental Inspection, Testing, Diagnosis, Repair
InspectAPedia ® Home
WATER ENTRY IN BUILDINGS
AGE of MOLD - Old is the Mold?
BASEMENT CEILING VAPOR BARRIER
BASEMENT MOLD WATER IMPACT
BRICK WALL DRAINAGE WEEP HOLES
BUCKLED FOUNDATIONS due to INSULATION?
BUILDING DAMAGE ASSESSMENT & REPAIR
CONDENSATION on WINDOWS & SKYLIGHTS
DEW POINT TABLE - CONDENSATION POINT GUIDE
EFFLORESCENCE, Salts & White / Brown Deposits
FLOOD DAMAGE ASSESSMENT, SAFETY & CLEANUP
FLOOD DAMAGED FOUNDATIONS
FLOOD VENTS & FLOOD PORTS
FLOODS IN BUILDINGS-mold
FLOOR DAMAGE DIAGNOSIS
FOOTING & FOUNDATION DRAINS
FOUNDATION BULGE or LEAN MEASUREMENTS
FOUNDATION CRACKS & DAMAGE GUIDE
FREEZE-PROOF A BUILDING
FROST HEAVES, FOUNDATION, SLAB
HUMIDITY LEVEL TARGET
ICE DAM PREVENTION
MOISTURE CONTROL in BUILDINGS
MOLD INFORMATION CENTER
NOISE / SOUND DIAGNOSIS & CURE
ODORS & SMELLS DIAGNOSIS & CURE
SEWAGE BACKUP, WHAT TO DO
SEWAGE BACKUP TEST & CLEANUP
SEWAGE BACKUP PREVENTION
SEWAGE PUMP CLOG DAMAGE
STAIN DIAGNOSIS on BUILDING EXTERIORS
STAIN DIAGNOSIS on BUILDING INTERIORS
SWEATING (CONDENSATION) on PIPES, TANKS
TOILETS, INSPECT, INSTALL, REPAIR
TRAPS on PLUMBING FIXTURES
VAPOR BARRIERS & CONDENSATION in BUILDINGS
VENTILATION in BUILDINGS
WATER ENTRY in BUILDINGS
WINTERIZE A BUILDING
Advice for using spray sanitizers, sealants, disinfectants in crawl spaces following crawl space cleanup or mold removal. Using a sealant can reduce future mold growth and help keep a crawl space dry - steps that in turn may also improve building indoor air quality - but don't rely on sprays alone to "cure" a wet, damp, moldy, or contaminated crawl area..
This article series describes the steps needed to get into, inspect, clean, and then dry out a building crawl space. We give a step by step crawl space entry, inspection, cleanout, dryout and keep dry guide explains how to get into or inspect a crawl space even if there is no ready access, how to assess crawl space conditions, how to stop water that is entering the crawl area, how to dry out the space, how to clean up and if necessary disinfect or sanitize the crawl space, and how to keep out crawl space water and moisture in the future.
Green links show where you are. © Copyright 2013 InspectAPedia.com, All Rights Reserved.
When Is it Good Practice to Use Biocides, Sanitizers, or Fungal sprays in a Crawl Space or in Other Building Areas?
For full details of this topic, please see MOLD SPRAYS, SEALANTS, PAINTS. The basics are just below.
When is it Good Practice to use Fungicidal Sealants and Encapsulant Sprays in a Crawl Space or in Other Building Areas?
For full details of this topic, please see MOLD SPRAYS, SEALANTS, PAINTS. The basics are just below.
Clean the crawl space, don't just spray it: Do not, however, permit the use of biocides, disinfectants, sprays, or encapsulants as a substitute for the physical cleaning that must come first.
Otherwise there is risk that you will leave harmful contaminants and particles in the building, and it is likely that cleanup will be inadequate. Look at the thick debris sprayed-over in this building. Simply stirring the debris shows that this approach was ineffective.
Fiberlok IAQ 6000 HD™ (above, left, misapplied right over a high volume of loose debris), Anabec X70™ waterborne sealant, and Fosters 4051™ (clear coating shown at above right) produce sealants frequently used by mold and flood damage remediation companies.
Once the crawl area has been cleaned of debris and moldy materials, and crawl space water has removed, and after we've eliminated the sources of crawl space water entry, we are ready to take the next steps to keep the crawl area clean and dry.
Details about use of fungicidal sealants and sprays are at MOLD SPRAYS, SEALANTS, PAINTS.
CRAWL SPACE REINSPECTION: Inspect the crawl space periodically to make sure your crawlspace dryout measures have been effective. How often do you need to inspect the area? It depends ... on site conditions and building history. At least once a year you should look for any new leaks such as a leaky plumbing drain or an outside water entry problem. If you have been having trouble keeping water out of the crawl area, you should check more often until your confidence is restored.
Watch out: for steps 1-7 above, in some conditions, dust containment, negative air, and more protective gear or help from professionals may be needed.
Also see our other crawl space dryout and safety discussions beginning at CRAWL SPACE GROUND COVERS where we describe crawl space venting, crawl space poly over dirt, and crawl space heat, to illustrate current best-practices in keeping a crawl space dry.
Separately our series of basement dry out, clean up and leak prevention articles begins at BASEMENT LEAKS, INSPECT FOR. Also see MOLD CLEANUP - MISTAKES to AVOID for a master list of the principal ways that people foul up mold cleanup projects.
Key building crawl space water entry diagnosis and cure articles:
Frequently Asked Questions (FAQs) about crawlspace de-watering: how to dryout the crawl space and how to keep that area dry
Question: using a sealer and vapor barrier in a crawl space
I live in the Wyoming mountains (9000 Ft) in a very dry climate, 15" of rain a year which includes average 3-4 feet of snow in the winter. The house is 45 years old. There were only two small vents in the crawl space. When an addition was built on the south end of the house 6 years ago,one vent was blocked by the addition which had a separate crawl space and vapor barrier installed. Last year we had record snowfall & high ground water, within 6" of outside grade.
I had a floor joists sagging in a bedroom and then I found white furry mold on a baseboard on the north end of the house. I pulled up the carpet and pad and on then inspected the crawl space below the two bedrooms found mold on the joists and subfloor with three joists rotting out under one bedroom and much less mold under the other bedroom which is on the other side of the main support beam..and a very wet space.
The vertical two by fours in the walls and blow-in insulation inspected so far are dry and show no mold. I had a contractor look at it and have decided to seal off the two bed rooms and remove the floors and joists completely in both rooms, remove a couple inches of dirt, dry out the crawl space, clean all the other visible mold by the methods you describe throughout the entire space, and rebuild the joists with pressure treated wood and new sub floors. And install more piers for support of the floor.
Do you have any comments or other suggestions? - J.R. Jay
JR even in a dry climate that has just periodic rainfall, leaks and water entry are asking for a mold or rot or insect problem. Your cleanup sounds thorough but I didn't see much about tracking down exactly where the water is leaking in. It's better to keep water out than to let it in and then get rid of it or to try to waterproof the interior against it.
I have now found that the water was migrating up from snowmelt to the sill plate on the top of the foundation. The contractor that did some repair of dry rot rim joist on the north end of the house before it was resided with stucco.
The contractor put Ice and Water Shield on the foundation down about 10 inches into the soil, and then had the Stucco contractor extend the 1/2" styrofoam board 12 inches into the soil as well thinking that all this would seal and insulate the foundation. When I pulled off the ice and water shield and the blue styrofoam the foundation was soaking wet underneath.
I have now removed all that mess and the foundation is drying out. With the amount of snowmelt that we have in the spring I think that is the main source of problem coupled with the reduced ventilation of only one small vent to the crawl space.
Question: how to dry out a crawl space after a toilet flood of more than 100,000 gallons into the crawl space
Our home flooded due to toilet break. 3 weeks water ran totaling 130,500 gallons of water. A company mediated our home, neglecting the crawl. I went under and dug down 6" the dirt was damp. How do we dry this out? - Ronald 7/22/12
Ronald I'd suggest starting crawl space dryout with a review of the suggestions in the article above - that's my best shot. When you've got the in crawl surfaces dry you'll want to take a look at the additional topics (see crawl space links near the top left of this page) such as how to put down a plastic moisture barrier to stop soil pumping moisture into the building.
Question: gutted house being renovated, mold like stuff on floor joists
I just bought a house that was mostly gutted when I got it. Neighbors tell of roof leaks and mold, though what was left on interior walls had no evidence of mold. Still, I finished the demo, removing everything down to stud walls and floor joists. Much of the subfloor (old chipboard and thin OSB - house was built in 1980) was rotted, to varying degrees. There was much mold-like substance on the floor joists - (I've been all over your website trying to determine the type) but they include the black cosmetic mold, brown fuzzy mold (not the hair-looking stuff, but sort of looked like spun cotton candy), white stuff, a little bit of yellow stuff. I'm using the folded rag method to clean with water and anti-bacterial soap, with a little bit of bleach for good measure. It seems to be working well.
My builder is now putting down new Advantek subfloor, as I'm finishing the cleaning. I'm also cleaning out the crawlspace as recommended, removing all the debris, the old poly, all insulation, etc. There is water encroachment during rains from one corner of the house where the gutters aren't working and the ground slopes towards the house.
Obviously, those last two things must be corrected immediately. The crawlspace had a few areas of standing water after the last significant rain. It had dissipated by the time I started the cleanup down there. However, under the plastic, some of the ground (red clay, here in NC) is pretty wet. Where I had removed the plastic, it has started to dry out pretty quickly. (three days?)
So, is it okay to let my builder complete the subfloor installation while I continue to clean the crawlspace, or would I be better served to have him wait to complete until I'm done? Should I leave the plastic off for a period of time to let the ground dry out before replacing it? also, there are a few small visible roots under there that themselves look moldy - black and spidery. What of that? The ground is uneven and I'll smooth it out to eliminate the low spots, but I'm uncertain as to what is the best next step. - Charlene Blevins 10/21/2012
Question: Hurricane Sandy flooded our Ocean City NY House - what do I do in the crawl space?
Hurricane Sandy hit my old Sears House (1930's)in Ocean City, NJ so the water was 1 foot deep on the first floor (the floor being 3 feet off the ground!) Sometime within the last 25 years the water was deep enough to get the insulation wet and it was removed at that time and not replaced (The house is not heated in the winter).
What should I do in the crawl space area? If I would encapsulate the crawl space, it would be like a swimming pool next time it floods. Ideas on a good solution? Is a spray insulating foam worthwhile for protecting flooring from underneath? Thanks!
I have also a home in Ocean City, NJ that got hit with Sandy. I have just pulled out the mostly wet insulation. I got water damaged in my first floor from the water seeping up from the craw space. Electric wires are down now and I am worried about structural damage.
Reply: tips for improving the resistance of crawl spaces to flood damage
Closed-cell foam products are somewhat resistant to wetting from flooding or other water intrusion in a building crawl space or anywhere else, but if a building area is actually inundated with floodwaters again after such an installation, I'd be concerned about the difficulty and cost of disinfecting or addressing the risks of sewage-contaminated floodwaters.
For this reason, just taking up some closed cell foam board can be problematic - how will you clean the space that was soaked with sewage waters between the foam boards and framing or subfloor above?
Talk with spray foam insulation contractors in your area about the water resistance of sprayed-in-place closed cell foam insulation. That product actually adheres to wood surfaces, a step that may resist sewage-contaminated water from entering the space between the insulation itself and wood surfaces that otherwise would need cleaning.
In addition, sealing the exposed wood and interior foundation surfaces with a sanitizing or fungicidal sealant (after they are thoroughly dry) will also reduce the moisture uptake (and sewage-contaminated water uptake) of those surfaces in future flooding, making surface cleaning and area dryout a bit faster after the next flood.
Frankly, if the home is likely to be flooded to a depth that submerges the first floor or higher, no crawl space encapsulation is going to completely protect the building; if you cannot afford to raise the building on a taller, flood-damage-resistant foundation or pier system, I'd be troubled about the prospect of recurrent, perhaps even increasingly frequent significant cleaning and repair costs from future area flooding.
Questions & answers or comments about how to dry out a wet crawl space & prevent future crawl space water entry.
Ask a Question or Enter Search Terms in the InspectApedia search box just below.
Technical Reviewers & References
Related Topics, found near the top of this page suggest articles closely related to this one.